Shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque must not be defined by property class 12.9, it...Meer tonen
Spherical washers and dished washers DIN 6319 are used for clamping on non-parallel surfaces. The dished washers type G with enlarged outside diameter are mainly used on...Meer tonen
Vorlegescheiben GN 184 werden mit Senkschrauben DIN ISO 2009 und DIN 7991 an den Stirnflächen der Wellenenden befestigt und schließen diese als Bund ab. Ein typisches...Meer tonen
Thrust pads DIN 6311 are used with grub screws DIN 6332 and tommy screws DIN 6304 or DIN 6306. Due to the pivoting connection between the thrust pin and thrust pad, they adapt...Meer tonen
T-nuts DIN 508 with the tensile strength class 8 (plain) are also available without thread. They can be adapted for special applications in this way.
Art.-Nr.
1076485
Leveranciersnummer
81265
EAN
4020772081263
Aantal
1 stuk
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...Meer tonen
Positioning elements GN 409.1 with threaded stud are designed for use as locating plungers, stops and thrust blocks.
Art.-Nr.
1076440
Leveranciersnummer
81778
EAN
4020772081775
VPE (Verpakking)
25 stuk
Aantal
1 stuk
The dimensions d2/ l1 of the cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2 and hubs with...
Art.-Nr.
1076486
Leveranciersnummer
80036
EAN
4020772080037
Aantal
1 stuk
Art.-Nr.
1076493
Leveranciersnummer
80069
EAN
4020772080068
Aantal
1 stuk
Art.-Nr.
1076483
Leveranciersnummer
80127
Aantal
1 stuk
Art.-Nr.
1251994
Leveranciersnummer
140327
EAN
4020772140328
Aantal
1 stuk
Threaded shaft collars GN 706.3 correspond in outer dimensions to the semi-split shaft collars GN 706.2. The bore has, however, an internal thread so that the clamping ring can...Meer tonen
Art.-Nr.
1076629
Leveranciersnummer
81349
EAN
4020772081348
Aantal
1 stuk
Art.-Nr.
1076630
Leveranciersnummer
84871
EAN
4020772084875
Aantal
1 stuk
Art.-Nr.
1076631
Leveranciersnummer
85480
EAN
4020772085483
Aantal
1 stuk
Art.-Nr.
1076628
Leveranciersnummer
84863
EAN
4020772084868
Aantal
1 stuk
Setting bolts GN 251 can be used as as a firm end stop as well as for support. The version with Polyurethane disk (type BK) functions as damping element or protection for...
Art.-Nr.
1076695
Leveranciersnummer
80911
EAN
4020772080914
Aantal
1 stuk
Art.-Nr.
1076743
Leveranciersnummer
82966
Aantal
1 stuk
Stainless steel spherical washers and dished washers DIN 6319 are used for clamping on non-parallel surfaces. Thanks to the material used, the spherical washers and dished...Meer tonen
Countersunk washers GN 184.5 are retained to the face of the shaft end with a countersunk head screw DIN ISO 2009 or DIN 7991 forming a clean-look end cap. A typical application...Meer tonen