Art.-Nr.
1076740
Leveranciersnummer
81117
EAN
4020772081119
Aantal
1 stuk
Art.-Nr.
1076759
Leveranciersnummer
87783
EAN
4020772087784
Aantal
1 stuk
Art.-Nr.
1076761
Leveranciersnummer
85720
EAN
4020772085728
Aantal
1 stuk
Art.-Nr.
1076762
Leveranciersnummer
80705
EAN
4020772080709
Aantal
1 stuk
Art.-Nr.
1076763
Leveranciersnummer
80713
Aantal
1 stuk
Art.-Nr.
1076764
Leveranciersnummer
80747
EAN
4020772080747
Aantal
1 stuk
Art.-Nr.
1076411
Leveranciersnummer
81893
EAN
4020772081898
Aantal
1 stuk
Art.-Nr.
1076408
Leveranciersnummer
81869
EAN
4020772081867
Aantal
1 stuk
Art.-Nr.
1076403
Leveranciersnummer
82016
EAN
4020772082017
Aantal
1 stuk
Art.-Nr.
1076399
Leveranciersnummer
82073
EAN
4020772082079
Aantal
1 stuk
Art.-Nr.
1076400
Leveranciersnummer
81984
EAN
4020772081980
Aantal
1 stuk
Art.-Nr.
1591594
Aantal
1 stuk
High-strength, straight shackles GN 584 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...Meer tonen
Ball point screws GN 606 with full ball (type A) are used in applications where a ball point contact is required. The flat faced moving ball (type B) allows a clamping or...Meer tonen
Ball transfer units GN 509 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The diameter...Meer tonen
Shaft collars GN 705 essentially comply with the versions of DIN 705. GN 705 also contains a number of practical intermediate sizes in addition to the DIN-versions as well as...Meer tonen
Stainless steel spherical washers and dished washers DIN 6319 are used for clamping on non-parallel surfaces. Thanks to the material used, the spherical washers and dished...Meer tonen
Hammerkopfmuttern GN 51b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...Meer tonen
Clamp spring washers GN 509.3, type A allow ball transfers units to be mounted and removed from the installation side. Retaining rings GN 509.3, type B are mounted from the...Meer tonen
Ball point screws GN 605 with full ball (type A) are used in applications where a ball point contact is required. The flat faced moving ball (type B) allows a clamping or...Meer tonen
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...Meer tonen
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...Meer tonen
Slotted locknuts GN 1804.1 are self-locking owing to their polyamide insert. They can therefore also be used as a setting nut and may be used more than once. The thread series...Meer tonen
High-strength, cranked shackles GN 585 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...Meer tonen